‘‘

ΉφΦιΛΏΈάΦ§³ΠΧωΦα³Π

Thrust Angular Contact Ball Bearings

Λ«ΟςΚάΑ¦

ZKLN‘­2RS

ZKLN‘­2ZΟ΅ΑΠ

‘‘

ΦαΎΆ ΠΝΊΕ ΦΨΑΏ ³ί΄η »ω±ΎΆξΆ¨ΤΨΊΙ Ό«ΟήΧͺΛΩ
Shaft Designation Mass Dimensions Basic Load Ratings Limiting
Diameter ‘‘ ‘‘ d D  B d1 D1 r1 r Ά―  Cr Ύ²  Cor Speed
‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ Dynamic Static ‘‘
mm ‘‘ g ‘‘ ‘‘ -0.25 ‘‘ ‘‘ min. min. kN kN rpm
12 ZKLN 1242.2RS 200 12 42 25 25.0 33.5 0.3 0.6 17.0 24.7 3800
‘‘ ZKLN 1242.2Z 200 12 42 25 25.0 33.5 0.3 0.6 17.0 24.7 7600
15 ZKLN 1545.2RS 210 15 45 25 28.0 36.0 0.3 0.6 17.9 28.0 3500
‘‘ ZKLN 1545.2Z 210 15 45 25 28.0 36.0 0.3 0.6 17.9 28.0 7000
17 ZKLN 1747.2RS 220 17 47 25 30.0 38.0 0.3 0.6 18.8 31.0 3300
‘‘ ZKLN 1747.2Z 220 17 47 25 30.0 38.0 0.3 0.6 18.8 31.0 6600
20 ZKLN 2052.2RS 310 20 52 28 34.5 44.0 0.3 0.6 26.0 47.0 3000
‘‘ ZKLN 2052.2Z 310 20 52 28 34.5 44.0 0.3 0.6 26.0 47.0 5400
25 ZKLN 2557.2RS 340 25 57 28 40.5 49.0 0.3 0.6 27.5 55.0 2600
‘‘ ZKLN 2557.2Z 340 25 57 28 40.5 49.0 0.3 0.6 27.5 55.0 4700
30 ZKLN 3062.2RS 390 30 62 28 45.5 54.0 0.3 0.6 29.0 64.0 2200
‘‘ ZKLN 3062.2Z 390 30 62 28 45.5 54.0 0.3 0.6 29.0 64.0 4300
35 ZKLN 3572.2RS 510 35 72 34 52.0 63.0 0.3 0.6 41.0 89.0 2000
‘‘ ZKLN 3572.2Z 510 35 72 34 52.0 63.0 0.3 0.6 41.0 89.0 3800
40 ZKLN 4075.2RS 610 40 75 34 58.0 68.0 0.3 0.6 43.0 101.0 1800
‘‘ ZKLN 4075.2Z 610 40 75 34 58.0 68.0 0.3 0.6 43.0 101.0 3300
50 ZKLN 5090.2RS 880 50 90 34 72.0 82.0 0.3 0.6 46.5 126.0 1500
‘‘ ZKLN 5090.2Z 880 50 90 34 72.0 82.0 0.3 0.6 46.5 126.0 3000
Λ΅Γχ£Ί ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘
1.±νΦΠΛωΑΠ»ω±ΎΆξΆ¨ΤΨΊΙ‘’Ό«ΟήΧͺΛΩΊΝΦΨΑΏ£¬½φΉ©Ρ‘Τρ²ΞΏΌΣΓ‘£ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘
2.Φα³Π΅Δ±£³ΦΌάΘηΣΙΛάΑΟΦΖ³Ι£¬ΤΚΠνΉ€ΧχΞΒΆΘ£Ί120‘ζΑ¬Πψ£¬180‘ζΆΜΖΪ‘£ ‘‘ ‘‘ ‘‘
‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘
Note: ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘ ‘‘
1.These load, speed and mass is reference of choice only.   ‘‘ ‘‘
2.If the cages are made of plastics, the maximum allowable working themperrature is 120‘ζ in 
  continuous working and 180‘ζ in short working.